Now booking fall roof inspections. Get your roof checked before snow and plan next season's coating work. Book free inspection →
A finished shop with interior spray foam insulation on the walls and underside of the roof deck
Interior spray foam insulation

Spray Foam Insulation for Montana Shops, Commercial Buildings & Homes

Insulation is a big part of what we do. We spray open-cell and closed-cell foam inside metal buildings, shops, pole barns, warehouses, and houses across western Montana to seal air leaks, add R-value, and stop the condensation that drips from cold steel. Your insulation estimate is free.

Why spray foam

Insulation and air sealing in one step

Most buildings in Montana don't lose heat because there's no insulation at all. They lose it through gaps: open seams in metal walls, rim joists, top plates, roof-to-wall joints, and the hundreds of small cracks that let warm air escape and cold air in. Fiberglass batts slow heat but let air move right through them.

Spray foam goes on as a liquid, expands to fill those gaps, and bonds to the surface it's sprayed on. That gives you insulation and an air seal in a single layer, shaped to the building instead of cut to fit.

  • Air sealing. Fills cracks, seams, and irregular framing that batts and boards leave open.
  • R-value where you need it. Closed-cell foam packs the most insulation into a thin space; open-cell is a cost-effective way to fill deep cavities.
  • Condensation control on metal. Foam sprayed tight to steel keeps warm, moist air off the cold panels.
  • Lower energy use. Less air leakage and better insulation mean the heater runs less. We won't promise a number because every building is different.
  • A quieter, less drafty building. Sealing gaps cuts drafts and outside noise, and closed-cell foam adds stiffness to metal panels.

Homes & commercial buildings

Get your free insulation estimate

Rather talk? Call or text 406-210-3168 · Mon–Fri 8 AM–5 PM MT

Your insulation estimate is free, with no obligation. We use your details only to contact you about your building.

Open-cell vs. closed-cell

Two kinds of foam, chosen for the building

There are two main types of spray foam. Neither is "better" everywhere. We pick the one that fits the space, the moisture conditions, and your budget, and some buildings get both.

Open-cell foamClosed-cell foam
What it isSoft, spongy, lightweight foam that expands a lot to fill cavitiesDense, rigid foam that cures hard
Insulation per inchLower R-value per inch, so it's applied thickerHigher R-value per inch, good for tight spaces
Air sealingExcellentExcellent
MoistureLets water vapor pass through; not for areas that get wetSlows water vapor at the right thickness and resists water
StrengthFlexible, adds no strengthAdds rigidity to walls and metal panels
Where we use it mostInterior walls and roof decks of homes, sound control, deep framing cavitiesMetal buildings, pole barns, rim joists, crawlspaces, foundation walls, and anywhere condensation is a problem
CostLower cost to fill a deep cavityHigher cost per inch, more performance per inch
Where we spray

Commercial buildings, ag buildings, and homes

From a 40 by 60 shop to a warehouse or an old farmhouse, the goal is the same: stop the air leaks, insulate the right surfaces, and manage moisture so the building stays dry.

Metal buildings & warehouses

Closed-cell foam sprayed on the underside of the roof panels and the walls insulates, air-seals, and controls the condensation that drips from bare steel onto equipment, inventory, and floors.

Shops & garages

Heated shops and garages get warmer and hold heat longer. Foam seals the seams, overhead-door headers, and roof-to-wall joints where cold air pours in.

Pole barns & ag buildings

Machine sheds, horse barns, and ag buildings with metal skin and open framing are a natural fit for spray foam, especially where condensation and drafts are a problem.

Offices, retail & churches

Walls, roof decks, and hard-to-reach cavities in occupied commercial buildings, planned around your schedule so you can keep working.

Homes & cabins

Exterior walls, cathedral and vaulted ceilings, bonus rooms, and additions where there's little space for insulation and air leaks are hard to chase.

Attics, crawlspaces & rim joists

Rim joists and band boards are one of the leakiest spots in a house. We also insulate crawlspace and foundation walls and the attic roof deck when an unvented attic is the right design.

Metal buildings

Stop the "rain" inside your metal building

If your shop or barn drips on cold mornings, that's condensation, not a roof leak. Warm air inside picks up moisture from vehicles, people, livestock, concrete, and heaters, then hits the cold steel overhead and turns to water. Over time it rusts panels and fasteners, soaks insulation, and drips onto whatever is underneath.

Closed-cell spray foam applied directly to the roof panels and walls keeps that warm, moist air from ever touching the steel. Because it bonds to the metal, there are no seams or gaps for air to sneak behind, which is where faced batts and loose blankets often fail.

We also check the other half of the problem: where the moisture comes from and how the building is ventilated. Sometimes the fix includes better exhaust, a vapor barrier under a slab, or changing how the building is heated.

Already have a leaking or rusted metal roof on top? See our metal roof restoration work. We'll fix the roof and the insulation in the right order.

Interior spray foam insulation on the walls of a large building, with radiant floor tubing laid out for the slab
A Revive interior spray foam job: foam sprayed on the walls of a large building, with radiant floor tubing laid out for the slab.
Winter in Montana

Icicles, ice dams, and heat loss

Big icicles and thick ridges of ice at the eaves aren't just a winter look. They usually mean heat is leaking out of the house, melting snow on the roof, and letting the water refreeze at the cold edge. That ice can back water up under shingles and metal, stain ceilings, and rot roof decking.

Because we're roofers, we look at it from both sides. We find where warm air is escaping into the attic or roof assembly, air-seal and insulate it with spray foam or blown-in insulation, and make sure the roof is ventilated correctly so the deck stays cold and dry.

Learn more in our homeowner guides on ice dams on Montana homes and what icicles and snow melt say about heat loss.

Moisture & ventilation

Done right, or not at all

Spray foam changes how a building breathes. Seal a building tight without thinking about moisture and fresh air, and you can trade drafts for damp walls or stale air. That's why we plan every job around how the building handles moisture:

  • Vented or unvented attic. We decide whether to insulate the attic floor and keep the attic vented, or bring the attic inside by foaming the roof deck, and detail it to match.
  • The right foam on the right surface. Closed-cell foam where vapor and water are a concern; open-cell where the assembly needs to dry.
  • Fresh air and exhaust. Bath fans, dryer vents, and kitchen exhaust go outside, not into the attic. Tighter homes and shops may need planned ventilation.
  • Fix leaks first. We don't foam over a roof leak or wet framing. Those get fixed before insulation goes in.
  • Code and fire protection. Foam gets the thermal or ignition barrier the building code requires for the space.

How a spray foam job works

  1. Walkthrough

    We look at the building, the existing insulation, moisture problems, ventilation, and the roof, then recommend foam type, thickness, and where it goes.

  2. Free written estimate

    A clear scope and price at no cost, so you know exactly which surfaces get what.

  3. Prep & protect

    We mask windows, floors, equipment, and anything that stays in the building, and seal off the work area.

  4. Spray

    Foam is applied in passes to the planned thickness, with people and pets out of the area.

  5. Ventilate, clean up & check

    The area is ventilated as the product requires, trimmed where needed, cleaned up, and checked for thickness and coverage before you move back in.

Our work

Recent interior spray foam work

Photos from Revive insulation jobs in western Montana. More job photos will be added as they come in.

A finished shop with interior spray foam insulation on the walls and underside of the roof deck
A finished shop with spray foam on the walls and the underside of the roof deck.
Interior spray foam insulation on the walls of a large building, with radiant floor tubing laid out for the slab
Interior spray foam on the walls of a large building, with radiant floor tubing laid out for the slab.

Spray foam insulation across western Montana

We insulate homes, shops, and commercial buildings across western Montana, including Missoula, Kalispell, Whitefish, Columbia Falls, Bigfork, Lakeside, Polson, Ronan, Plains, Hot Springs, Thompson Falls, St. Regis, Superior, Libby, Eureka, and the Bitterroot Valley. Don't see your town? Call or text 406-210-3168.

Not sure spray foam is the right fit? Many attics are better served by blown-in fiberglass or cellulose, and some buildings need a combination. See the insulation overview, or just tell us about the building and we'll give you a straight recommendation.

FAQ

Spray foam insulation FAQ

What's the difference between open-cell and closed-cell spray foam?

Open-cell foam is soft and spongy, expands a lot, and is a strong air seal at a lower cost per inch, but it lets water vapor pass through. Closed-cell foam is dense and rigid, has a higher R-value per inch, and at the right thickness also slows water vapor, which is why it's often used on metal buildings, rim joists, and crawlspaces. We recommend one, or a mix of both, based on the building, not a default.

Can you spray foam the inside of a metal building or pole barn?

Yes. Metal shops, warehouses, pole barns, and ag buildings are some of the most common places we use spray foam. Sprayed directly onto the underside of the roof panels and the walls, closed-cell foam insulates and air-seals in one step and keeps warm, moist inside air off the cold steel, which is what causes condensation and dripping.

Will spray foam stop my metal building from dripping?

Condensation happens when warm, humid air touches cold metal. Spray foam applied tight to the steel keeps that air from reaching the panels, which is one of the most effective ways to control it. We also look at where the moisture is coming from, such as vehicles, livestock, wet concrete, or unvented heaters, because ventilation and moisture sources are part of the fix.

Is spray foam a good fix for ice dams and big icicles?

Often, yes. Ice dams and heavy icicles usually come from warm air leaking out of the house and melting snow on the roof. Air-sealing and insulating the attic or roof deck stops a lot of that heat loss. Because we're roofers too, we look at the roof, the attic, and the ventilation together so we fix the cause and not just the symptom.

How much will spray foam save on my heating bill?

It depends on the building, how leaky and under-insulated it is now, how you heat it, and how you use it, so we won't promise a number. What we can tell you is that air leaks and missing insulation are some of the biggest sources of heat loss in Montana buildings, and spray foam addresses both at once.

Do I need to leave the house while you spray?

Yes. People and pets stay out of the work area while foam is being sprayed and until the area has been ventilated and the foam has cured as the product's instructions require. We'll give you the timeline for your job before we start, and we seal off and protect the rest of the building.

Does spray foam need to be covered?

In many places, yes. Building codes generally require foam plastic insulation to be separated from living or working space by a thermal barrier, such as drywall, or by an ignition barrier or approved coating in attics and crawlspaces. We'll plan the job so it meets the code requirements that apply to your building.

Is the spray foam estimate free?

Yes. We'll look at the building and give you a written insulation estimate for free, with no obligation.

Is spray foam on the inside the same as a spray foam roof?

No. A spray foam roof system goes on top of the roof and is covered with a protective coating to keep the weather out. Interior spray foam insulation goes on the inside of the walls, roof deck, attic, or crawlspace to stop heat loss and air leaks. We do both, and on some buildings it makes sense to look at them together.

Free insulation estimates

Ready to stop paying to heat the outdoors?

Tell us about your shop, building, or home. We'll look at the insulation, the air leaks, the moisture, and the roof, and give you a clear recommendation and a free, no-obligation estimate.

Before you go

Your first commercial roof inspection is free.

Find out whether your roof can be restored instead of replaced. No obligation.

Schedule My Free Inspection406-210-3168